{"id":191,"date":"2023-11-09T13:00:35","date_gmt":"2023-11-09T04:00:35","guid":{"rendered":"https:\/\/www.ffcam.makino.co.jp\/products\/ffaut-en\/?page_id=191"},"modified":"2023-12-04T16:57:19","modified_gmt":"2023-12-04T07:57:19","slug":"v230","status":"publish","type":"page","link":"https:\/\/www.ffcam.makino.co.jp\/products\/ffaut-en\/products\/vup\/v230\/","title":{"rendered":"FFAUT V.23.0"},"content":{"rendered":"\n

Version comparison : V.23.0<\/h1>\n\n\n
\n\t\n\n\t\n\t
\n\t\t\t\t\t

Contents outline<\/h2>\n\t\t\n\t\t
<\/div>\n\t<\/div>\n<\/div>\n<\/div>\n\n\n\n

Machining Function<\/h2>\n\n\n\n

Added Light Chamfering Function to 2D Route Machining<\/h3>\n\n\n\n

Chamfer cutters can now be set for 2D Route Machining.
Settings have been added for light chamfering.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

[Output Only to Plane Part] Function Has Been Added to the [Plane Auto Recognition] Function of Contour Rough Machining<\/h3>\n\n\n\n

If the [Output Only to Plane Part] function is used, a contour face cut machining path is output only for the surfaces that are automatically recognized as planes (red frame in the image below). This can reduce the machining time.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

Added a Function to Automatically Set the Setting Values of [Minimum Uncut Detection] of Uncut Part Machining with a Percentage Value of the Tool Diameter<\/h3>\n\n\n\n

On the machine parameters setting screen, the initial values of [Min. Uncut Detection] of each machining can be now changed to a percentage value of the tool diameter.<\/p>\n\n\n\n

Added a Function for the Automatic Setting of the Setting Values of [Area Detection Accuracy] of Contour Projection Machining with Automatically Calculated Values<\/h3>\n\n\n\n

On the machine parameters setting screen, the initial values of [Area Detection Accuracy] of contour projection machining can now be changed to automatically calculated values.<\/p>\n\n\n\n

Improvement to Enable Setting the NC File Extension for Each Machine<\/h3>\n\n\n\n

The NC file extension to be output can now be set for each machine.
The setting items of [NC File Extender] of machine parameters have been moved from [NC Output Parameters] to [FFPOST PARAMETERS] of each machine.<\/p>\n\n\n\n

Improvement to Enable the Setting of [Safety Mode at Hole ATC] for Each Machine<\/h3>\n\n\n\n

The setting items of [Safety mode at hole ATC] in the machine parameters have been moved from [NC Output Parameters] to [Machine Parameters] for each machine.<\/p>\n\n\n\n

Added New Models to the Machine List of Machine Parameters<\/h3>\n\n\n\n

The following models have been added.<\/p>\n\n\n\n

iQ500,V100S,v61,a71nx,a92,a120nx<\/span><\/p>\n\n\n\n

The addition of the models are also reflected in the model name selection of the process data.<\/p>\n\n\n\n

Operation<\/h2>\n\n\n\n

Improvement to the Setting Items of the Tool Cutting Edge Length Parameters<\/h3>\n\n\n\n

In FFAUT V.23, the value set for [Cutting Edge Length] in the [Tool Selection] screen is output to the tool data that is prepared in CSG Interface and Vericut.<\/p>\n\n\n\n

Specific Half-Width Symbols Can Now Be Used for the Project Name in the Professional Data Output Screen<\/h3>\n\n\n\n

Improvement has been made to enable input of \u201c- (hyphen)\u201d and \u201c_ (underscore)\u201d to [Project Name] in the [Professional Data Output] screen.
<\/p>\n\n\n\n

FF\/SIM<\/h2>\n\n\n\n

Added a Function to Set a Random Color for Rest Models and Corner R<\/h3>\n\n\n\n

When auto setting the setting color, select [Gradient color] or [Random color] from the pull-down menu of the [Auto Setting] button.<\/p>\n\n\n\n

\n
\n
\"\"
Rest Model Color Setting Screen<\/figcaption><\/figure>\n<\/div>\n\n\n\n
\n
\"\"
Corner R Color Setting Screen<\/figcaption><\/figure>\n<\/div>\n<\/div>\n\n\n\n

Changed the Initial Values for the Interference Check Condition of the Simulation Settings<\/h3>\n\n\n\n

Changed the check conditions of [Interference Detection Setting] of [Simulation Setting] to perform the interference check operation with the initial values.
Interference detection of following items will also be performed automatically when the simulation is executed.<\/p>\n\n\n\n